This is a special, built-to-order, mono version of Etna λ Lambda for real mono playback of monaural/monophonic (mono) microgroove, vinyl records. It is recommended that the Etna λ Lambda Mono is used with high-gain, low noise phono stages, or alternatively a step-up transformer designed for phono cartridges of 2 - 3 ohms or less.
On mono records, the vertical axis of the groove contains no musical information, but it will frequently have noise, in the form of groove damage and dirt. The Etna λ Lambda Mono has therefore been designed to be completely insensitive to the vertical axis, which greatly improves the signal/noise ratio without any downside on monaural records.
The coil former is a square permeable plate oriented parallel to the record surface rather than the 45-degree angle used for most stereo cartridges, while the coils are wound so that they only generate a signal when there is horizontal movement of the stylus and cantilever when tracking a record. Two totally separate monaural coils are used in the Etna λ Lambda Mono, since most monaural cartridges are used with stereo amplifiers and stereo speakers. The separate coils also help avoid possible ground loops and hum problems that could otherwise be caused if a single coil is fed into a stereo two-channel amplification system, thereby tying the two channels together electrically.
In addition to parallel mono connection to a stereo system (two amplifiers and two speakers), it is also possible to leave one set of connections unattached for pure mono playback with a single amplifier and a single speaker. However, it is also possible to connect the two mono channels in series for additional output when used in a pure mono system. Use a short cartridge headshell lead wire with female pin-connectors to connect either the Etna λ Lambda Mono's upper right pin with the lower left pin, or alternatively the upper left pin with the lower right pin. Then use the two remaining unused pins for connection to your single amp RIAA input (alternatively a transformer input). The two internal channels are now "chained" in serial-connection for additional output and energy when you only use a single amplifier and a single speaker.
The Etna λ Lambda Mono uses Lyra’s "New Angle" technology, which mechanically pre-biases the signal coils so that they are perfectly aligned to the front and rear magnets when LP playback takes place. This equalizes out discrepancies in vertical and horizontal compliances and enables the Etna λ Lambda Mono coils to move with equal ease in all directions for optimal performance.
A seldom-mentioned yet key factor in defining the performance and sound of a phono cartridge is the suspension and damper system. A cantilever’s materials, dimensions and constructions all affect the sound in unique ways, and unless the dampers and suspension are engineered to be a suitable match to the cantilever chosen, the sound and performance will not be optimal.
For Lyra’s post-2008 New Angle models (Delos, Kleos, Etna, Atlas) we developed tapered dampers to pre-load the cantilever downwards when it is in the rest position, so that the application of vertical tracking force (VTF) will bring the coil angle into alignment with the magnets when the cartridge is in the playing position. Our continued research into dampers and suspension systems has now led to the next level up - Lambda.
Lambda separates the tapered dampers of the New Angle cartridges into flat elastomer discs (for damping) and an additional support “pillow” to serve as the cantilever pre-loading element. This division allows the use of more specialized materials that are better suited to their individual tasks.
The Lambda Atlas and Etna thereby continue the New Angle benefits (coil and magnet angles become aligned when the cartridge is in the playing position), but stability and sonic performance are significantly improved.
The Lambda improvements apply to both the single coil layer models (Atlas SL, Etna SL) and the standard double coil layer models (Atlas, Etna). Likewise for the Atlas Mono and Etna Mono models.
We endeavour to despatch same day for orders placed up to 12 noon on available stock items (items with stock message "Usually dispatched within 24 hours"). Please remember to check with us first for a physical stock check if next day delivery is important to you. Any items with stock message "Usually dispatched within 72 hours" are items that we do not hold in stock but order in from the importer or manufacturer as soon as a customer order is received. Occasionally these may be delayed beyond 72 hours due to importer/manufacturer stock levels but we will inform you as soon as we can if this is the case.
UK ORDERS: We despatch the bulk of our UK mainland items on a 24 hour service – Free of Charge. Non Mainland locations - Isle of Man, Isle of Wight, the Scilly Isles, the Scottish highlands and Islands, the Channel Islands and Northern Ireland may take a day or so longer and are not Free of Charge. Smaller items are delivered using Royal Mail recorded delivery or special delivery. Larger items are delivered using a courier service such as Interlink Express, DPD, UPS or DHL.
INTERNATIONAL ORDERS: We offer competitive rates which can be confirmed by email. Please just ask – we will need a full delivery address and telephone number. Smaller items are delivered using Royal Mail Small Packets Airmail with International Tracked and/or Signed depending on value of item and availability of the service. Larger International shipments are sent by insured and tracked services using DPD, DHL or UPS. If there are any delays due to specific customs regulations, etc, you will be contacted by Turntableworld or by the courier with a request for any further information required. Customs duties do not apply for shipments into any EU country (for a full list please refer to the EU Country List). Customs duties can apply for countries outside of the EU. Customers in these countries are responsible for all taxes and duties incurred when the items enter their country.
COLLECT IN STORE OR HOME INSTALL:At the request of the manufacturer some items cannot be supplied by mail order but you can click and buy them and then elect to collect them from our store or arrange a home install (if applicable). Applicable items clearly state that they are Collect in store or home install. Once ordered you will receive a message prompting you to contact us by phone or email to arrange for us to deliver and install or to reserve and collect from our store at your convenience, you will also be advised of the delivery time / stock availability as not all Home install / collect in store items are held in stock.