Michell Coated Suspension Springs

Rubber-coated suspension springs bring a significant upgrade to all pre-2021 GyroDec / Gyro SE / Orbe / Orbe SE Turntables. By damping the spring's natural ability to resonate when exposed to airborne vibrations, the rubber coating prevents the music playing in the room from feeding vibrations back into the turntable. This small innovation gives a significant increase in performance. Bass response is tightened, and instruments and vocals are more defined within the sound stage.

Pro-Ject VTA-IT Tonearm Spacer

The VTA-IT is a 1.5mm tonearm spacer, allowing you to increase the vertical tracking angle of your turntables tonearm. With VTA-IT you will be able to install a larger variety of cartridge types on your tonearm or headshell.  Please Note: The installation of “VTA-IT“ should be done by an experienced technician.  Compatibility: Debut I-III Debut Carbon Debut Carbon EVO Essential I-III (only standard configurations) Required Tools: Philips #1 Screwdriver & 5.5mm Nut Driver Wrench

Michell Standard Gyro Arm Plate

Michell can supply a range of arm plates for use on their turntables. Standard patterns include Rega, SME, Linn, Hadcock and Graham.

Pro-Ject Signature Tonearm

The Signature tonearms from Pro-Ject Audio Systems offer true audiophile sound and striking style. They represent the absolute best performance possible. Key Features: Single-pivot tonearm design with minimal friction Available in 10" and 12" length Stunning high-gloss finish Non-magnetic low resonance construction Accomodates a wide range of cartridges, including SPU models Aluminium headshell with built-in fingerlift included High-conductivity Oxygen-Free Copper (OFC) headshell cables included Built-in 5-pin DIN connector (tonearm cable not included) VTA, azimuth and overhang adjustment all easily accessible Selection of set-up tools included

Rega RB330 Stainless Steel Counterweight

Replacement counterweight for the RB330 tonearm.   Please Note: The RB330 tonearm comes as standard on the following turntables. Planar 3 - Mild Steel Planar 6 - Stainless Steel This counterweight is also compatible with the RB303 tonearm.

Pro-Ject Replacement Counterweight

The purpose of a counterweight is to apply the optimum down force for your pick-up cartridge to read the most amount of detail within the record groove.

Rega RB110 Mild Steel Counterweight

Replacement counterweight for the RB110 tonearm.   Please Note: The RB110 tonearm comes as standard on the following turntables. Planar 1 Planar 1 Plus This counterweight is also compatible with the RB101 tonearm.

Audio-Technica AT6006R Tonearm Safety Raiser

AT6006R Tonearm Safety Raiser.   Key Features: Lifts tonearm automatically at the end of a record, protecting stylus tip Hydraulic lift with rubber lift bar operates safely and smoothly Can be mounted on a variety of turntables with different tonearm heights

Rega Three Point Tonearm 2mm VTA Spacer

A 2mm stainless spacer, laser cut from 2mm stainless steel or anodised black aluminium. Fits all Rega three point tonearms including the 2016 range of Planar turntables. This spacer replaces the previous plastic spacer and offers better performance and support for the tonearm. Please Note: Rega turntables spacers should not be necessary unless you are you using an exceptionally deep bodied cartridge from another manufacturer.

Rega RB220 Mild Steel Counterweight

Replacement counterweight for the RB220 tonearm. Please Note: The RB220 tonearm comes as standard on the following turntables. Planar 78 Planar 2 This counterweight is also compatible with the RB202 tonearm.

Rega RB880 Stainless Steel Counterweight

Replacement counterweight for the RB880 tonearm. Please Note: The RB880 tonearm comes as standard on the following turntables. Planar 8 This counterweight is also compatible with the RB808, RB330 and RB303 tonearms.

Rega RB3000 Tungsten Counterweight

Replacement counterweight for the RB3000 tonearm.   Please Note: The RB220 tonearm comes as standard on the following turntables. Planar 10 This counterweight is also compatible with the RB2000 and RB1000 tonearms.

Rega RB330 Mild Steel Counterweight

Replacement counterweight for the RB330 tonearm.   Please Note: The RB330 tonearm comes as standard on the following turntables. Planar 3 - Mild Steel Planar 6 - Stainless Steel This counterweight is also compatible with the RB303 tonearm.

Rega Three Point Tonearm Plastic VTA Spacer

All in one 2mm, 4mm, 6mm and 8mm height adjustment spacer for Rega three point tonearms. When Rega arms are fitted to turntables from other manufacturers it may be necessary to add our "Rega arm spacers" to achieve the correct arm height.

Rega Single Point Tonearm 2mm VTA Spacer

Arm Height Adjustment spacer for RB250 and RB300 - size 2mm.   When Rega arms are fitted to turntables from other manufacturers it may be necessary to add Rega arm spacers to achieve the correct arm height.   Circular spacers are available for the RB250 and RB300 in thickness' of 2mm. An arm 'Sleeve nut' is also available for circumstances where the arm base does not protrude below the arm mounting board.   Please Note: Turntable spacers are not necessary on all Rega turntables.