Michell Apollo Phono Stage & Muse Power Supply

For discerning audiophiles, the true allure of vinyl lies in the richness and warmth of analogue sound. To fully appreciate every detail and nuance, the right equipment is essential. While a premium turntable, tonearm, and cartridge are vital, the quality of your phono stage is what ensures the integrity of the music.  Crafted in the UK and meticulously designed by the Michell Audio team, the Apollo incorporates cutting-edge technology to deliver outstanding audio performance with any turntable and cartridge. This two-box design is engineered to minimise unwanted RF noise, as such interference is the most damaging external factor to the delicate circuits of a phono stage, ensuring pristine audio reproduction. Key Features: The inbuilt power supply circuitry works in harmony with the MUSE power supply to further refine and regulate the DC power High-Quality class A preamplifiers ensure precise signal handling Passive RIAA Circuit Class A Gain Stages Customisable loading and gain settings. MUSE uses a high-quality low noise toroidal transformer, advanced capacitance multiplier technology and very high-quality voltage regulators, to reduce ripple and noise, delivering two highly filtered and regulated DC outputs. Dual Filtration: It works in harmony with APOLLO's internal power supply for superior filtering and regulation. Noise Isolation: By housing the transformer separately in MUSE, any noise generation is isolated from the amplification circuits.

Michell LEVIS Magnetic Levitation Feet

LEVIS feet use opposing magnets to support your turntable, allowing it to float on a cushion of air. This innovative design adds an extra layer of structural isolation between your turntable's sensitive components and the surface it rests on. Structural vibrations can be caused by dynamic forces from loudspeakers, foot traffic, nearby traffic, electrical transformers, and even turntable motors. Even the smallest vibrations can transfer to your turntable and impact its performance. LEVIS feet effectively eliminate these vibrations before they become an issue. When designing a magnetic levitation device, it's crucial to control the levitation mechanism and ensure the assembly remains intact. After exploring existing solutions, we decided on a fully enclosed design with minimal contact points. In operation, each foot features only three tiny, unloaded contact points—almost pinpoints—made from high-rigidity, low-mass polymer. These contact points do not bear weight and are isolated from the metal components by a polymer housing and spring. Their sole purpose is to prevent metal parts from touching, resulting in an exceptionally low level of contact and maximising contact-free support. LEVIS feet are sold in sets of three and come in two weight ranges: LEVIS (for full-size turntables with hinged lids, 13kg-30kg) LEVIS SE (for SE model turntables, 9.5kg-14kg)

Michell GyroDec Suspension Springs and Adjuster Kit

Upgrade kit for original specification GyroDecs with single-piece steel suspension pillars, This kit now includes rubber-coated suspension springs. This upgrade simplifies adjusting the chassis height and spring position, enabling you to perfectly set up your turntable. With the turntable now effectively supported on three pin points, performance is also enhanced. Unlike the original design, the suspension pillar consists of three parts: a suspension spindle, thrust ball, and hollow pillar. The spindle is fixed to the base of the turntable, with the thrust ball at its top. The hollow pillar encases this assembly and supports the spring, which in turn holds the chassis. This configuration provides a three-position, high-pressure, point contact suspension system, minimising structural vibrations from reaching the sensitive components of the turntable.

Michell Coated Suspension Springs

Rubber-coated suspension springs bring a significant upgrade to all pre-2021 GyroDec / Gyro SE / Orbe / Orbe SE Turntables. By damping the spring's natural ability to resonate when exposed to airborne vibrations, the rubber coating prevents the music playing in the room from feeding vibrations back into the turntable. This small innovation gives a significant increase in performance. Bass response is tightened, and instruments and vocals are more defined within the sound stage.

Michell Record Clamp

Michell record clamp for use on GyroDec, TecnoDec, or third-party turntables.   Available with a black or silver knob.

Michell R Record Clamp

Michell 'R' record clamp for use on Rega and similar third party turntables with short centre spindles. Available with a black or silver knob.

Michell VTA Adjuster 3

Please Note: This is compatible with Rega tonearms using the redesigned three point fixing base such as the RB220, RB330. The Michell VTA adjuster 3 allows you to easily adjust the height of your tonearm, so it is perfectly level no matter what cartridge you choose to use. Correctly setting the vertical tracking angle (VTA) and subsequently the stylus rake angle (SRA) for your cartridge, allows the stylus to perfectly track the vinyl groove, optimising the amount of detail extracted from the recording.

Michell VTA Adjuster 2

Please Note: This is compatible with Rega tonearms and derivatives using the original three point fixing base such as the RB202, RB303. The Michell VTA adjuster 2 allows you to easily adjust the height of your tonearm, so it is perfectly level no matter what cartridge you choose to use. Correctly setting the vertical tracking angle (VTA) and subsequently the stylus rake angle (SRA) for your cartridge, allows the stylus to perfectly track the vinyl groove, optimising the amount of detail extracted from the recording.

Michell Iso Base

Compatible with the Orbe SE, Gyro SE and TecnoDec the Iso Base is the ideal platform to place your Michell Engineering turntable.   Its inert material characteristic combined with the tenderfeet give it the extra isolation that is necessary for the very best performance from your deck.

Michell Locknut and VTA Adjuster Pack

Twin pack consisting of: Finger Locking nut (to suit Rega arms) A Vertical Tracking Angle adjustment sleeve for the Rega RB-250, RB-300 and RB-600 arms, to be used with the new-style Rega arm board Michell have been making since the beginning of 1999.  If used with other turntable brands, slight enlargement of the original Rega mounting hole will be necessary to accommodate the increased diameter of the VTA sleeve.

Michell Synthetic Turntable Bearing Oil

Michell use a proprietary synthetic oil to lubricate the main bearing in all their turntables. The oil has to be a precise viscosity to enable the inverted bearings to circulate the oil correctly.

Michell UniCover Dust Cover

The UniCover is a great solution for people who have an open style turntable with no hinged lid and want to keep the essential parts of their turntable dust free. Please Note: This is also compatible with the TecnoDec and SE model turntables.

Michell VTA Adjuster 1

Please Note: This is compatible with Rega tonearms and derivatives using a threaded base, such as the RB250, RB300. The Michell VTA adjuster 1 allows you to easily adjust the height of your tonearm, so it is perfectly level no matter what cartridge you choose to use. Correctly setting the vertical tracking angle (VTA) and subsequently the stylus rake angle (SRA) for your cartridge, allows the stylus to perfectly track the vinyl groove, optimising the amount of detail extracted from the recording.

Michell Hydraulic Reference Drive Belt

Please Note: This will only fit the Hydraulic Reference turntable. All Michell turntable drive belts are made of a proprietary rubber compound, designed to keep your vinyl revolving at precisely the correct speed, while also minimising any vibration transfer from the motor to the turntable.

Michell SEcure Cover Dust Cover

Available to fit the Orbe SE and Gyro SE, the SEcure Cover has been designed to totally cover the whole deck (platter, motor and arm assembly) and is the best solution to keep your naked Michell Engineering turntable free of dust.

Michell Drive Belt

Please Note: This is for all Michell turntable models except the Reference Hydraulic. All Michell turntable drive belts are made of a proprietary rubber compound, designed to keep your vinyl revolving at precisely the correct speed, while also minimising any vibration transfer from the motor to the turntable.

Michell GyroDec/Orbe Arm Plate Decoupling Kit

Available to original GyroDec / Orbe owners whose turntable has the arm plate attached using long screws and straight through spacers.   The new assembly isolates the arm plate from the chassis of the turntable using a redesigned arm plate spacer.